How to Measure a Furniture Lock: Barrel Length, Hole Diameter, and Mounting Dimensions
Nov 13, 2026
Leave a message
How to Measure a Furniture Lock: Barrel Length, Hole Diameter, and Mounting Dimensions
|
Meta Title |
How to Measure a Furniture Lock: Dimensions & Sizing Guide |
|
Meta Description |
Learn how to measure a furniture lock correctly - barrel length, mounting hole diameter, cam dimensions, and door thickness - so you order the right replacement every time. |
|
Focus Keyword |
how to measure a furniture lock |
|
Secondary Keywords |
lock barrel length, mounting hole diameter, cam lock size, furniture lock dimensions |
Introduction
Ordering the wrong furniture lock is one of the most common problems in the industry. The lock arrives, and then you discover the barrel is 3 mm too short, the mounting hole is the wrong diameter, or the cam does not reach the strike.
Almost every one of these problems is preventable with a tape measure and a few minutes of careful work. This guide shows you how to measure a furniture lock correctly.
The Five Key Measurements
Before you order, capture these five dimensions:
1. Barrel length
2. Mounting hole diameter
3. Panel (door or drawer) thickness
4. Cam length and shape
5. Overall body length and head diameter
Let us look at each one.
1. Barrel Length
The barrel (or cylinder body) is the part that passes through the panel. Its length determines how much material the lock can clamp.
How to measure: Measure from the underside of the head (the flange that sits against the front of the panel) to the end of the threaded barrel.
What to check: The barrel length must be longer than the panel thickness plus the washer and nut. If the panel is 18 mm and the hardware stack adds 3 mm, you need a barrel longer than 21 mm.
Common barrel lengths: 10, 16, 20, 25, and 30 mm.
2. Mounting Hole Diameter
This is the hole drilled through the panel to accept the lock.
How to measure: Use calipers or measure the diameter of the hole directly.
What to check: Most cam locks use a 19 mm (approx. 3/4 inch) hole, but smaller sizes such as 12 mm and 16 mm are also common. Ordering a 19 mm lock for a 16 mm hole simply will not fit.
3. Panel Thickness
The panel is the door, drawer front, or cabinet wall.
How to measure: Measure the thickness of the material at the point where the lock will mount, not somewhere else on the cabinet.
What to check: Panel thickness plus the fastener stack must be less than the barrel length. Leave a small margin so the nut can be tightened.
4. Cam Length and Shape
The cam is the rotating arm that does the locking. Its length determines how far it reaches behind the frame, and its shape determines whether it clears the frame correctly.
How to measure: Measure the cam from the centre of the mounting hole to the tip, and note the offset.
What to check: Cam lengths are often quoted as 20 mm, 25 mm, 30 mm, etc. Match the old cam exactly, or measure the required reach from the lock centre to the strike point.
5. Overall Body and Head Diameter
The head is the visible face of the lock. It must match the existing hole and the aesthetic of the furniture.
How to measure: Measure the diameter of the head and the total length of the lock from head to cam tip.
What to check: A larger head may not sit flush in a recessed hole. A smaller head may look out of proportion.
Step-by-Step Measuring Checklist
1. Remove the existing lock if possible and measure it directly.
2. Record panel thickness at the mounting point.
3. Measure the mounting hole diameter with calipers.
4. Measure barrel length from the head underside to the end.
5. Measure the cam from the pivot centre to the tip.
6. Note the rotation angle (90 or 180 degrees).
7. Photograph the lock next to a ruler for reference.
Tips for Measuring Without Removing the Lock
If you cannot remove the lock:
• Measure the visible head diameter and the amount of barrel protruding at the back.
• Use the panel thickness plus the protrusion to estimate barrel length.
• Measure the cam reach through the open door.
• Compare dimensions against a supplier catalogue to identify the model.
Why the Rotation Angle Matters
A 90-degree lock and a 180-degree lock are not interchangeable in every application. If the cam must swing a full half-turn to clear the frame, a 90-degree lock will not work. Always confirm the rotation from the old lock or from the application drawing.
Common Measurement Mistakes
• Measuring the panel at the wrong point (thicker or thinner than the mounting area).
• Forgetting the washer and nut thickness in the barrel calculation.
• Using a ruler for a hole that needs calipers.
• Ignoring cam offset, not just cam length.
• Assuming all 19 mm locks are identical - they are not.
Conclusion
Learning how to measure a furniture lock takes only a few minutes but saves time, money, and returns. Measure the barrel length, hole diameter, panel thickness, cam geometry, and rotation angle before you order - and always keep a record of the dimensions for future replacements.
Send Inquiry


